Counter and Timer 2 in 1 unit

● Digital programmable timer● 48mm*48mm,72mm*72mm,96mm*96mm● Panel mount type● Dry contact, NPN input● Maximum 4 outputs(Relay or SSR Drive)● 85~265Vac or 24VDC source● Perfect for Ozone generators, can control up to several loads

● Digital programmable timer● 48mm*48mm, LCD display,6 digits● Display format,00.00.00, seconds,minutes,hours● Panel mount type● Dry contact, NPN input● Maximum 4 outputs(Relay or SSR Drive)● 85~265Vac or 24VDC source

● Digital programmable counter● 48mm*48mm,Dual line 4 digits display● Panel mount type● Dry contact, NPN input● Maximum 2 outputs(OP1 and OP2)● 85~265Vac or 24VDC source● SV counting/Batch counting/Totalizing count

● Digital programmable counter● Dual line 6 digits LCD display● Panel mount type● Dry contact, NPN input● Maximum 4 outputs(OP1 and OP2)● 85~265Vac or 24VDC source● SV counting/Batch counting/Totalizing count

The NTC10K Series is a compact, high-precision Negative Temperature Coefficient (NTC) thermistor temperature sensor housed in a rugged stainless steel M8 screw-body probe. Designed for direct installation into threaded ports on pipework, tanks, heat exchangers, and machinery, this sensor delivers accurate, low-cost temperature measurement across a wide operating range without the need for signal conditioning or cold-junction compensation.At the heart of the sensor is a precision NTC thermistor element with a nominal resistance of 10 kΩ at 25 °C and a B-value (B25/100) of 3950 K ± 1%. The thermistor element is encapsulated within a 4 mm diameter stainless steel probe, sealed with high-temperature epoxy resin to ensure moisture ingress protection. The M8 threaded body incorporates a high-temperature silicone gasket to provide a leak-proof seal when installed into a threaded port. A 150 mm flat silicone lead wire terminates in a standard 2-pin SMP (Micro-Fit style) connector for fast, tool-free connection to the host system.The NTC10K series is fully compatible with Maxwell's range of temperature controllers, as well as third-party controllers, HVAC control boards, and microcontroller-based systems that accept a passive NTC thermistor input. The sensor's small probe diameter, short lead wire, and plug-and-play connector make it an ideal drop-in component for OEM equipment manufacturers and system integrators.

The MKD2 Series is a single-phase, dual-channel, DC-controlled AC solid state relay (SSR) designed for reliable, silent switching of resistive and inductive AC loads in industrial and commercial control systems. Each unit houses two independent switching channels within a single compact black housing, enabling two separate AC loads to be controlled simultaneously from a single device — saving panel space and wiring time compared to installing two separate SSRs. The MKD2 accepts a DC control voltage of 4–32 VDC, making it directly compatible with PLC outputs, microcontroller I/O, and standard industrial control signals. The AC load side supports voltages from 24 to 480 VAC, covering 110 V, 220 V, 380 V, and 480 V systems worldwide. Load current ratings of 25 A, 40 A, 60 A, and 80 A are available, with all variants sharing the same physical footprint for easy interchangeability. Zero-crossing trigger technology ensures that switching occurs at the natural zero-crossing point of the AC waveform, minimising electrical interference (EMI) and extending the service life of both the relay and the connected load. Individual LED status indicators for each channel provide instant visual confirmation of relay state, simplifying commissioning and fault-finding. The unit is CE certified and constructed from fire-retardant ABS with a dielectric strength of 2500 Vrms between input, output, and base.

MF43HYC-669 is a touch screen temperature controller with timer, used in various industrial ovens, like hot air oven, laboratory Ovens, autoclave, drying ovens, powder coating ovens, curing ovens, sterilization ovens etc, Basically this controller offers a perfect solution for any oven needs to be controlled precisely on both temperature and time. Some of large ovens with a circulation fan in the system, this controller has an independent control button, you can run the circulation fan at any time you want to help with the even distribution of the heat during the heating process and drive extra heat away after work done.  Cell phone APPs on both IOS and Android platform makes it possible to remotely control and monitor the system from anywhere any time from any part of the world as long as you have internet access. PC access and control is also possible via webpage server.

4 digits Temperature controller, Universal input(TC/RTD), relay and SSR drive output field selectable. various size available, AC source or DC source optional.parameter reset function to help you go back to factory default.