6 Digits LCD Display Counter

● Digital programmable timer● 48mm*48mm,72mm*72mm,96mm*96mm● Panel mount type● Dry contact, NPN input● Maximum 4 outputs(Relay or SSR Drive)● 85~265Vac or 24VDC source● Perfect for Ozone generators, can control up to several loads

● Digital programmable timer● 48mm*48mm, LCD display,6 digits● Display format,00.00.00, seconds,minutes,hours● Panel mount type● Dry contact, NPN input● Maximum 4 outputs(Relay or SSR Drive)● 85~265Vac or 24VDC source

● Digital programmable timer+counter,● 48mm*48mm,Dual line 4 digits display● 2 in1 timer+counter● Various timer triggering mode● OP1 output for timer and OP2 output for counter● 85~265Vac or 24VDC source● Perfect solution for application need timer and counter

● Digital programmable counter● 48mm*48mm,Dual line 4 digits display● Panel mount type● Dry contact, NPN input● Maximum 2 outputs(OP1 and OP2)● 85~265Vac or 24VDC source● SV counting/Batch counting/Totalizing count

The NTC10K Series is a compact, high-precision Negative Temperature Coefficient (NTC) thermistor temperature sensor housed in a rugged stainless steel M8 screw-body probe. Designed for direct installation into threaded ports on pipework, tanks, heat exchangers, and machinery, this sensor delivers accurate, low-cost temperature measurement across a wide operating range without the need for signal conditioning or cold-junction compensation.At the heart of the sensor is a precision NTC thermistor element with a nominal resistance of 10 kΩ at 25 °C and a B-value (B25/100) of 3950 K ± 1%. The thermistor element is encapsulated within a 4 mm diameter stainless steel probe, sealed with high-temperature epoxy resin to ensure moisture ingress protection. The M8 threaded body incorporates a high-temperature silicone gasket to provide a leak-proof seal when installed into a threaded port. A 150 mm flat silicone lead wire terminates in a standard 2-pin SMP (Micro-Fit style) connector for fast, tool-free connection to the host system.The NTC10K series is fully compatible with Maxwell's range of temperature controllers, as well as third-party controllers, HVAC control boards, and microcontroller-based systems that accept a passive NTC thermistor input. The sensor's small probe diameter, short lead wire, and plug-and-play connector make it an ideal drop-in component for OEM equipment manufacturers and system integrators.

The MKD2 Series is a single-phase, dual-channel, DC-controlled AC solid state relay (SSR) designed for reliable, silent switching of resistive and inductive AC loads in industrial and commercial control systems. Each unit houses two independent switching channels within a single compact black housing, enabling two separate AC loads to be controlled simultaneously from a single device — saving panel space and wiring time compared to installing two separate SSRs. The MKD2 accepts a DC control voltage of 4–32 VDC, making it directly compatible with PLC outputs, microcontroller I/O, and standard industrial control signals. The AC load side supports voltages from 24 to 480 VAC, covering 110 V, 220 V, 380 V, and 480 V systems worldwide. Load current ratings of 25 A, 40 A, 60 A, and 80 A are available, with all variants sharing the same physical footprint for easy interchangeability. Zero-crossing trigger technology ensures that switching occurs at the natural zero-crossing point of the AC waveform, minimising electrical interference (EMI) and extending the service life of both the relay and the connected load. Individual LED status indicators for each channel provide instant visual confirmation of relay state, simplifying commissioning and fault-finding. The unit is CE certified and constructed from fire-retardant ABS with a dielectric strength of 2500 Vrms between input, output, and base.

This is a single phase SCR power regulators and temperature controllers 2 in 1 units, in a typical heating system, you would need a temperature controller and a SCR power regulators, and they are two separate devices, we go further and build this two devices in one package, this saves a lot of efforts for panel builders when it comes down to wiring, and RS-485 modbus is a standard feature, controller can be integrated to systems with HMI or PLC etc. the load can be directed wired to this thyristor power regulators, and it works with all kinds of inputs, Thermocuple, RTD, analog signal

The MW10E is a highly advanced, microprocessor-based single-phase SCR power regulator designed for industrial heating and power control applications. Featuring a wide input voltage range, dual analog control inputs, and robust protection mechanisms, this controller ensures precise power regulation, enhanced system reliability, and real-time monitoring. Its compact, lightweight design, combined with high-performance heat dissipation, makes it an ideal solution for demanding industrial environments