DC Input AC Load 3 Phase Solid State Relays

● Three phase solid state relay● 5-32Vdc input● 24~480Vac load● only available with 10/25/40 amps● Zero-crossing trigger● For resistive load only

● Three phase solid state relay● 90~280Vac Input● 24~480Vac load● From 10 amps up to 200 amps● Zero-crossing trigger

The MW30E series is an advanced, three-phase power regulator (current range: 25–1500A), Suitable for both resistive and inductive loads 1. Rating from 25A all the way up to 1500A2. 0-5V/0-10V/0-20mA/4-20mA analog input, 3 digital inputs, 1 digital output, Modbus-RTU3. Phase angle firing control mode or burst-firing mode configurable4. Work with load on Star, Delta or Star with netural wire5. Modbus RS-485 available as default,  other communication like profibus DP, Ethernet can be custom made6. Different control mode, Constant Voltage (V) / Constant Current (I) / Constant Power (P)/Open-loop7.100% load can be applied to the SCR according to the rating, for example, 100 amps rating SCR, you can apply 100 amps to phase current. there is no need to take the derating into consideration

The MKD2 Series is a single-phase, dual-channel, DC-controlled AC solid state relay (SSR) designed for reliable, silent switching of resistive and inductive AC loads in industrial and commercial control systems. Each unit houses two independent switching channels within a single compact black housing, enabling two separate AC loads to be controlled simultaneously from a single device — saving panel space and wiring time compared to installing two separate SSRs. The MKD2 accepts a DC control voltage of 4–32 VDC, making it directly compatible with PLC outputs, microcontroller I/O, and standard industrial control signals. The AC load side supports voltages from 24 to 480 VAC, covering 110 V, 220 V, 380 V, and 480 V systems worldwide. Load current ratings of 25 A, 40 A, 60 A, and 80 A are available, with all variants sharing the same physical footprint for easy interchangeability. Zero-crossing trigger technology ensures that switching occurs at the natural zero-crossing point of the AC waveform, minimising electrical interference (EMI) and extending the service life of both the relay and the connected load. Individual LED status indicators for each channel provide instant visual confirmation of relay state, simplifying commissioning and fault-finding. The unit is CE certified and constructed from fire-retardant ABS with a dielectric strength of 2500 Vrms between input, output, and base.

The NTC10K Series is a compact, high-precision Negative Temperature Coefficient (NTC) thermistor temperature sensor housed in a rugged stainless steel M8 screw-body probe. Designed for direct installation into threaded ports on pipework, tanks, heat exchangers, and machinery, this sensor delivers accurate, low-cost temperature measurement across a wide operating range without the need for signal conditioning or cold-junction compensation.At the heart of the sensor is a precision NTC thermistor element with a nominal resistance of 10 kΩ at 25 °C and a B-value (B25/100) of 3950 K ± 1%. The thermistor element is encapsulated within a 4 mm diameter stainless steel probe, sealed with high-temperature epoxy resin to ensure moisture ingress protection. The M8 threaded body incorporates a high-temperature silicone gasket to provide a leak-proof seal when installed into a threaded port. A 150 mm flat silicone lead wire terminates in a standard 2-pin SMP (Micro-Fit style) connector for fast, tool-free connection to the host system.The NTC10K series is fully compatible with Maxwell's range of temperature controllers, as well as third-party controllers, HVAC control boards, and microcontroller-based systems that accept a passive NTC thermistor input. The sensor's small probe diameter, short lead wire, and plug-and-play connector make it an ideal drop-in component for OEM equipment manufacturers and system integrators.

Maxwell DR8F-T-U06 is a din rail mount 8 input 8 transistor outputs I/O modules, input can be NPN or PNP input, 8 NPN transistor output can be controlled from master device like HMI or PLC, the input work independently apart from output.

Maxwell DR02B is a din rail mount PID temperature controller, 2 channel configuraitons, support thermocouple inputs(K,E,J,N,W,S,T,R,B), and output can be Relay, SSR Drive, it's a very simple din rail mount ccontroller, PID or ON/OFF control mode, RS-485 modbus communication as standard features, 85~265Vac source for easy system intergration, auto-tuning for both loops and with an external plug and play external configruation devices. the field configuration will be very easy to carry out.

TT-513 is a cost-effective din rail mounted temperature transmitter, it is 1 input and 1 output version, available with 4-20mA and 0-10Vdc output, works with TC/RTD input, such as type K, PT100, you can programmable the input and range via PC software and cell phone APP( cell phone app available on Android device)